home 제품소개
TEKTRONIX
TEKTRONIX
전체 오실로스코프 신호발생기 전원공급기 스펙트럼분석기 프로브 및 악세사리

TBS2000 시리즈

  • 2 and 4 analog channel models
  • 100 and 70 MHz bandwidth models
  • Up to 1 GS/s sampling rate
  • 20 M record length on all channels
  • 5 year warranty
  • 9-inch WVGA color display
  • 15 horizontal grids show 50% more signal
  • TekVPI probe interface supports active, differential, and current probes with automatic scaling and units
  • 32 automated measurements, and FFT function for thorough waveform analysis
  • HelpEverywhere provides helpful on-screen tips
  • Built-in Scope Intro handbook provides operating instructions and oscilloscope fundamentals
  • 2-channel models are highly-portable at 2.62 kg (5.8 lbs
  • USB 2.0 host port on the front panel for quick and easy data storage
  • Wi-Fi interface provides wireless communications capability 1 support
  • USB 2.0 device port on rear panel for easy connection to a PC
  • LXI compliant 10/100BASE-T Ethernet port for remote control over LAN



← 사진을 클릭하면 큰 사이즈로 보실 수 있습니다.

제품목록 온라인문의
사양
모델명 TBS2072  TBS2102  TBS2074  TBS2104 
대역폭 70MHz 100MHz 70MHz 100MHz
채널 2 2 4 4
각 채널별샘플링속도 1.0GS/s 1.0GS/s 1.0GS/s 1.0GS/s
Hardware bandwidth limits

20 MHz

Input coupling

DC, AC, or GND

Input impedance

1 MΩ ± 2 %, 11.5 pF ± 2.5 pF

Input sensitivity range

2 mV/Div to 5 V/Div

Vertical resolution

8 bits

Maximum input voltage, 1 MΩ

300 V RMS with peaks ≤ ±450 V

Acquisition modes

Sample

- Acquire sampled values.

Peak Detect

- Captures glitches as narrow as 3.5 ns at all sweep speeds.

Average

- From 2 to 512 waveforms included in average.

Hi-Res

- Averages multiple sample of one acquisition interval into one waveform point.

Roll

- Scrolls waveforms right to left across the screen at sweep speeds slower than or equal to 40 ms/div (400 ms/div at 20M record length).

Math modes

All units:

Ch 1 - Ch 2

Ch 2 - Ch 1

Ch 1 + Ch 2

Ch 1 X Ch 2

FFT

4 channel units:

Ch 3 - Ch 4

Ch 3 + Ch 4

Ch 4 - Ch 3

Ch 3 X Ch 4

DC balance

± (1 mV +0.1 div)

DC gain accuracy

± 3% 10 mV/div through 5 V/div-

± 4% typical 2 mV/div and 5 mV/div

DC voltage measurement accuracy average mode

Average of > 16 waveforms

±((DC Gain Accuracy) X |reading - (offset - position)| + Offset Accuracy + 0.11 div + 1 mV)

Delta Volts between any two averages of ≥16 waveforms acquired with the same oscilloscope setup and ambient conditions

±(DC Gain Accuracy X |reading| + 0.08 div + 1.4 mV) 

Maximum duration of time captured at highest sample rate (all channels)

40 ms

Time base range

2 ns/div to 100 sec/div

Trigger modes

Auto, Normal, and Single

Trigger holdoff range

20 ns to 8 s

Trigger types

Edge

- Positive or negative slope on any channel. Coupling includes DC, HF reject, LF reject, and noise reject.

Pulse width

- Trigger on width of positive or negative pulses that are >, <, =, or ≠ a specified period of time.

Runt

- Trigger on a pulse that crosses one threshold but fails to cross a second threshold before crossing the first again.

Automated measurements 

32, of which up to six can be displayed on-screen at any one time. Measurements include: Period, Frequency, Rise Time, Fall Time, Positive Duty Cycle, Negative Duty Cycle, Positive Pulse Width, Negative Pulse Width, Burst Width, Phase, Positive Overshoot, Negative Overshoot, Peak to Peak, Amplitude, High, Low, Max, Min, Mean, Cycle Mean, RMS, Cycle RMS, Positive Pulse Count, Negative Pulse Count, Rising Edge Count, Falling Edge Count, Area, Cycle Area, Delay FR, Delay FF, Delay FR, and Delay RR. 

Display type

9 inch (228 mm) wide format liquid crystal TFT color display.

Display resolution

800 horizontal by 480 vertical displayed pixels (WVGA).

 

 

Go Top